|
  
Introduce to you
The full information оn " Granulator-30 " :
The Instruction of the user:
1) . This model desktop granuljatora motorized continuous
Actions. You can make skilled and small-scale parties of granules
In diameter from 0.5мм up to 5 mm. Granuljator-30 can be maintained only in
Automatic режиме.
2). Laboratory granuljator it is used in the industry for release
Pharmaceutical and chemical production, the foodstuffs, granules medical
Purposes. In all cases when it is required to receive granulated
The powder of Granuljator-30 is suitable for use in laboratory
Or for manufacture of small parties продукции.
3). it is not necessary to use granuljator for granulirovanija strongly
Damp, coarse-grained powders and other kinds of raw material not intended
For job with desktop гранулятором.
Technical parameters:
4). the Basic characteristics and productivity:
Volume of loading of the bunker kg 3
The maximal diameter of granules (мм) 5
The minimal diameter of granules (mm) 0.5
The maximal productivity kg / hour 40
Capacity of the engine 0,55 kW
Weight (kg) 70
Overall dimensions: Height (mm) 750
Length and Width (mm) 460Х500
Characteristics Granulator:
5). the Body granuljatora - a bed of the basis the cast case, on
Which the basic shaft is combined with blades. The shaft passes through the bunker, in
Which is fallen asleep the dry or humidified powder. From the bottom party of the bunker,
In special fastenings, the sieve (a metal grid) stretches.
The wiping mechanism will consist of 5 blades which are combined on a shaft.
Rotating, blades wipe portions of a powder through apertures of a sieve. Ready
Granules are poured in a tray.
6). All process of job granuljatora can be divided on: (a) .Zapolnenie
The bunker powder
(b) .Protiranie a powder through net
(c). Reception ready гранул
These three actions are carried out continuously and can be adjusted, that
To execute observance of parameters of the received granules.
7). Granuljator-30 is the compact, desktop device for
Long job. After you fix granuljator on a table
Screws, you can use it. Granulator-30 is applicable for mobile
Manufactures.
Instruction on adjustment:
8). Installation replaceable net:
At job with Granulator you can operatively change the size of granules. For
It it is necessary to prepare rectangular preparations of a metal grid
In the sizes 270мм h 205 мм . Attention - for job with food kinds of raw material
Use only corrosion-proof and brass grids. For industrial raw material-
A usual steel grid. In some cases it is possible to use
A polyethylene grid. From the bottom party of the bunker two shaft are fixed with
prorezju. It is necessary to pass edges of a grid in the data prorezi on both platens. With
An end face shaft come to an end handles, rotating for which simultaneously in
Opposite directions, you can pull a grid. Adjust
A level of a tension of a grid also record screws position of a shaft. On everyone
To a shaft is small shesternja with mobile clamps. Having placed
In a groove shesterni you fix a clamp net.
9). Loading of the bunker by a powder:
Before to load a powder in the bunker, be convinced, that the sieve is established with
In the necessary size of a cell, check up a tension of a grid. Necessarily
Check structure of powder weight. A design granuljatora
Provides continuous submission of small portions of a powder. Maximal
Weight of loading of a powder (damp) 3 kg. As required add
A new powder during job granuljatora. Watch on filling of a tray
Granules.
the Instruction on service:
1 0 ). Greasing of details granuljatora. Having turned off
The top and back covers put greasing on all mobile parts granuljatora.
Especially it is necessary to watch greasing shesterni coil
1 1 ). It is required to check mobile parts
granuljatora periodically to see, presence of greasing and their status of friction.
If there will be defects, the serviceman should correct in due time them before
Uses Granulator.
1 2 ). After the termination of job, a part of a powder
Should be removed. To clean a surface of the bunker and the blade a brush. If
granuljator it will not be used during long time, to remove a sieve,
To clean granuljator completely and to wipe dry.
1 3 ). the Sieve after dismantle to wash out hot
Water with washing means..
Notes:
1 4 ). In job pay attention to quality
Received granules if you have noticed, that granules differ on the size and
There are distortions of the form stop to use the worn out sieve. From quality
A grid (sieve) in many respects quality and uniformity of the received granules depends.
1 5 ). do not use too much damp powder,
Since it can promote zalipaniju cells of a sieve.
1 6 ). At job granuljatora avoid
Hits of extraneous subjects in driving parts of the mechanism. All adjustments
To make after a full stop Granulator and disconnect from a network
Power supplies.
1 7 ). Watch closely, that greasing not
Got in the bunker with a powder. Since parts of greasing can get in ready
Granules and to spoil quality.
18 ). At greasing details Granulator
Watch, that surpluses of greasing did not accumulate.
19 ). Being near to working Granulator
Watch closely, his technical status.
2 0 ). Job with Гранулятором-30 has to spend
In a premise with temperature of +18 degrees, with humidity of air no more than 70
%.
2 1 ). To jobs on editing, connection,
To adjustment and maintenance service Granulator experts are supposed with
Corresponding skills and education.
2 2 ). Partial or full non-observance of rules
The operation, listed in the given Instruction, deprives with you the right on
Warranty service besides the manufacturer and the seller do not bear
The responsibility for breakages Granulator and the traumas received in result
Such infringements.
We offer you
our link base:
OUR WEB SITES
and USEFUL LINKS.
Free small video
clips about our equipment :
|
